Agilent's general-purpose septa are made from an enhanced injection-molded silicone rubber material. The septa material, dark red or gray in color, is specified to withstand over 200 automatic injections at an injection port temperature of 350 °C. You can have confidence in your chromatographic…

Single septa for 13-425 screw caps from MACHEREY-NAGEL PTFE virginal: temperature resistant: –200 °C / +260 °C, very high analytical purity, very hard (but very thin material), no resealability Red Rubber / TEF (FEP): temperature resistant: –40 °C / +110 °C, medium…

Low bleed, longer life alternative to standard septa for split/splitless injection Has a lifetime of more than 2000 injections, depending on samples and operating conditions Reduced instrument downtime for septa changes and injection port liner changes due to septa particulates Two…

Agilent now coats each premium 11-mm inlet septa with plasma to eliminate sticking in the GC inlet. With our premium non-stick septa, you'll never have to scrape bits of septum out of your inlet. Our premium septa also have a recess on the injection side that guides the syringe needle to the same…

Agilent now coats each premium 11-mm inlet septa with plasma to eliminate sticking in the GC inlet. With our premium non-stick septa, you'll never have to scrape bits of septum out of your inlet. Our premium septa also have a recess on the injection side that guides the syringe needle to the same…

Agilent now treats each premium 11 mm inlet septa to eliminate sticking in the GC inlet. With our premium non-stick septa, you'll never have to scrape bits of septum out of your inlet. Agilent's premium septa also have a recess on the injection side, to guide the syringe needle to the same point…

Agilent's general-purpose septa are made from an enhanced injection-molded silicone rubber material. The septa material, dark red or gray in color, is specified to withstand over 200 automatic injections at an injection port temperature of 350 °C. You can have confidence in your chromatographic…

GC injection port septa Standard quality Septum grade: Standard septa (ST) Material: beige silicone Thickness: 4 mm Hardness: 60° shore A Septum grade: High temperature septa (HT) Material: red non-bleeding silicone Thickness: 3 mm Hardness: 60° shore A …

The Agilent Technologies inlet septa is made from strong silicone material and works well even at 35 degree C temperatures. This septa is compatible to use with 5880, 5890, 4890, 6850, 6890, 7890 GC columns. Application: For 5880, 5890, 4890, 6850, 6890, 7890 GCs This product is only available…

Replacement septa for 8-425 screw caps from MACHEREY-NAGEL PTFE virginal: temperature resistant: –200 °C / +260 °C, very high analytical purity, very hard (but very thin material), no resealability Red Rubber / TEF (FEP): temperature resistant: –40 °C / +110 °C,…

Septa closure with locking flange for open-top caps. Flat stopper; thin flange Cap size: 33 mm Gray Chlorobutyl/50 septa

PTFE Disk septa are chemically inert PTFE Red Rubber septa are economical for many GC applications PTFE/Silicone septa are most popular for HPLC and IC applications Pre-slit septa are easier to pierce with thin gauge needles

Agilent now coats each premium 11-mm inlet septa with plasma to eliminate sticking in the GC inlet. With our premium non-stick septa, you'll never have to scrape bits of septum out of your inlet. Our premium septa also have a recess on the injection side that guides the syringe needle to the same…

Agilent now treats each premium 11 mm inlet septa to eliminate sticking in the GC inlet. With our premium non-stick septa, you'll never have to scrape bits of septum out of your inlet. Agilent's premium septa also have a recess on the injection side, to guide the syringe needle to the same point…

Agilent now treats each premium 11 mm inlet septa to eliminate sticking in the GC inlet. With our premium non-stick septa, you'll never have to scrape bits of septum out of your inlet. Agilent's premium septa also have a recess on the injection side, to guide the syringe needle to the same point…

An improved version over the original Thermogreen LB-1 septa. Extremely low bleed over a wide range of inlet temperatures (100 °C to 350 °C) Already conditioned, ready to use Easier needle penetration and high puncture tolerance (ideal for autosamplers) Rubber formulation…

Designed for use with headspace autosamplers  for sealing sample vials used in operating temperature ranges of -60 to 200°C.  For aluminum seal finishes Clear FEP is 0.003" thick White silicone is 0.120" thick

Agilent now coats each premium 11-mm inlet septa with plasma to eliminate sticking in the GC inlet. With our premium non-stick septa, you'll never have to scrape bits of septum out of your inlet. Our premium septa also have a recess on the injection side that guides the syringe needle to the same…

Agilent now coats each premium 11-mm inlet septa with plasma to eliminate sticking in the GC inlet. With our premium non-stick septa, you'll never have to scrape bits of septum out of your inlet. Our premium septa also have a recess on the injection side that guides the syringe needle to the same…

Agilent's general-purpose septa are made from an enhanced injection-molded silicone rubber material. The septa material, dark red or gray in color, is specified to withstand over 200 automatic injections at an injection port temperature of 350 °C. You can have confidence in your chromatographic…

Three Layer Septa is made of preconditioned silicone rubber and is 3.81 mm (0.150 in.) thick. The average life of these septa is up to 100 injections with a 26s gauge needle. The maximum operating temperature is 200° C. Preconditioned silicone rubber septa, 3.81 mm (0.15“) thick …

Specially engineered to fit standard taper joints and tubes. Manufactured under white room conditions for extreme cleanliness. Made of a more dense rubber, low extractables and a better fit (50% to 80% on joints) these septa are much less likely to fail in the presence of solvents.

Agilent's general-purpose septa are made from an enhanced injection-molded silicone rubber material. The septa material, dark red or gray in color, is specified to withstand over 200 automatic injections at an injection port temperature of 350 °C. You can have confidence in your chromatographic…

Inlet septa are used to maintain a leak-free seal under the septum nut in the GC inlet, even after many repeated injections. The dimple in the middle of the septum guides the syringe needle through the inlet into the inlet liner to minimize damage to the needle and to ensure injection consistency.…

Agilent now coats each premium 11-mm inlet septa with plasma to eliminate sticking in the GC inlet. With our premium non-stick septa, you'll never have to scrape bits of septum out of your inlet. Our premium septa also have a recess on the injection side that guides the syringe needle to the same…

Inlet septa are used to maintain a leak-free seal under the septum nut in the GC inlet, even after many repeated injections. The dimple in the middle of the septum guides the syringe needle through the inlet into the inlet liner to minimize damage to the needle and to ensure injection consistency.…

22 mm Septa for VOA Vials PTFE/Silicone Liner

Low cost, good resealability Polytetrafluoroethylene provides barrier for product contact Red rubber

Agilent now coats each premium 11-mm inlet septa with plasma to eliminate sticking in the GC inlet. With our premium non-stick septa, you'll never have to scrape bits of septum out of your inlet. Our premium septa also have a recess on the injection side that guides the syringe needle to the same…

Agilent now treats each premium 11 mm inlet septa to eliminate sticking in the GC inlet. With our premium non-stick septa, you'll never have to scrape bits of septum out of your inlet. Agilent's premium septa also have a recess on the injection side, to guide the syringe needle to the same point…

Aluminum seals with pre-inserted septa are compatible with standard opening crimp top vials, wide opening Target LOVial™ crimp top vials and Target Snap-it™ crimp/snap vials.

Agilent now treats each premium 11 mm inlet septa to eliminate sticking in the GC inlet. With our premium non-stick septa, you'll never have to scrape bits of septum out of your inlet. Agilent's premium septa also have a recess on the injection side, to guide the syringe needle to the same point…